nAG
ohL
ocn
Thermoregulator TP-16.05 (further ‘device’), is used in de verwarming systems, in order naar besturing temperatuur of de heat-insulated floors, pools, greenhouses, refrigerators, freezing chambers en also voor no freezing of de spillways etc.
de instrument has monitoring of an open/short of de Sensor voor more comfortable Temperatuurregeling. de instrument has additional functions: setup of temperatuur of a hysteresis, a time delay op switching op of de relais, 3 operation modes: verwarming, cooling, a window; a panel of besturing buttons locking, function of connection de besturing buttons. Also de instrument doesn't require retuning in case of vermogen cutoff. All settings remain in a non-volatile memory.
Technical characteristics
Operating voltage ….…........................................................................................................................ 230V +/-20%
Full-load amperage …..........................................................................................................................16A/230V
vermogen consumption ….........................................................................................................................1 Of W
Sensor wire length as a set ….............................................................................................................2m
temperatuursensor application type …............................................................................................thermoresistor NTC 10kOm
Instrument operation mode …...........................................................................................................verwarming, cooling, interval
Hysteresis adjustable …......................................................................................................................1-70 °C
Response delay of relais …...............................................................................................................….0-250sek
Operating ambient temperatuur .......................................................................................................0-40 °C
Lower bound of temperatuur measurement …................................................................................-50 °C
Upper bound of temperatuur measurement …...............................................................................+125 °C
temperatuur accuracy…......................................................................................................................0,5 °C
Electronic lock of besturing buttons ..................................................................................................... is
Electronic switching off of de instrument met besturing buttons …................................................is
All parameters remain in a non-volatile memory
de default parameters
Desirable temperatuur …....................................................................................................................30 °C
Mode …..................................................................................................................................................nAG
Hysteresis …......................................................................................................................................….2 °C
Response delay of de instrument relais…........................................................................................00sek
Installation of desirable temperatuur
By short pressing de button ▼ of ▲ de device temporarily shows op de screen specified desirable temperatuur. voor de menu access voor changing de desirable temperatuur it is required naar press en hold down voor 2 seconds de button ▼ of ▲ changeable value of temperatuur will begin naar blink. Further de same buttons ▼ of ▲ naar set desirable temperatuur en naar fix de button B.
Installation of de "rEJ" mode
voor a start it is necessary naar access de menu of de device. voor this purpose it is required naar push en hold voor 2 seconds de button B. Then by short clicking op de same button naar select de rEJ submenu. Further met de button ▼ of ▲ naar select one of three options (de selected mode blinks) en naar press shortly de button B voor confirmation.
de instrument has three options of an operation mode:
1) nAG- verwarming
2) ohL- cooling
3) ocn- interval
in de section "Installation of temperatuur of a Hysteresis" you can review how these modes work.
Installation of temperatuur of a hysteresis "GSt"
voor a start it is necessary naar enter de menu of de device, voor this purpose it is required naar press en hold down voor 2 seconds de button B, then short pressing of de same button naar select de GSt submenu. Further naar set met de button ▼ of ▲ de required value of a hysteresis (changeable value blinks) en naar press shortly de button B voor confirmation.
How de hysteresis works?
When de mode of verwarming nAG is selected: if desirable temperatuur is set as 30 °C en de hysteresis will be set as 5 °C then relais of de device will turn op bij a temperatuur of 25 °C, en is disconnected when 30 degrees, thereby maintaining de temperatuur of 25-30 °C.
When de mode cooling ohL is selected: if desirable temperatuur is set as 30 °C en de hysteresis is set as 5 °C, then de relais of de device will turn op bij a temperatuur of 35 °C, en is switched-off bij 30 °C, thereby maintaining temperatuur of 35 en 30 °C.
When de mode window OCN is selected: if desirable temperatuur is set as 30 °C en de hysteresis is set as 5 °C, then de relais of de instrument will turn op bij de taken temperatuur from 25 °C naar 35 °C, en switched-off if de taken temperatuur is above 35 °C of below 25 °C.
Operation-time counter
This model of heat regelaar has a built-in operation-time counter. de time is calculated every second of de heat regelaar's operation en is saved in de device internal memory every 15 minutes, even in case of a vermogen cut. de calculated time is recorded in a heat regelaar's "trE" menu in increments of one hour. A maximum recorded value is equal naar 999 hours. When de maximum value is reached, de time count stops. You can resume counting by resetting de counter. de aim of this function is naar calculate energy consumed over a certain period of time, voor example, over a month. naar check of reset de recorded time you need naar enter de heat regelaar's menu. in order naar do it, press de "В" button en hold it voor 2 seconds. Then press de same button shortly en choose a trE submenu. After that you can access de trE submenu naar view de recorded time by pressing ▼ of ▲ buttons. in order naar reset de counter, use ▼ of ▲ buttons naar select “YES” value en press de B button shortly naar confirm your choice under de trE menu.
temperatuursensor calibration
First, you need naar access de regelaar’s menu. naar do it, press de "В" button en hold it voor 2 seconds. Then press de same button shortly en choose a Cor submenu. Use de ▼ of ▲ buttons naar set a correction (de changeable value will blink), en press de B button shortly voor confirmation.
Installation of response delay of de device relais voor de taken temperatuur changings "rEL".
voor a start it is necessary naar enter de menu of de device, voor this purpose it is required naar push en hold voor 2 seconds de button B, then by short clicking of de same button naar select de rEL submenu. Further de button ▼ of ▲ naar set de required delay period in seconds (de selected mode blinks) en naar press shortly de button B voor confirmation.
How de time delay works:
After de relais of de device turns op of turns off de loading it won't response naar changes of de taken temperatuur during de specifies time even if indications of de taken temperatuur will quit out of de set limits.
Note:
if there is no obvious need voor a time delay of reaction is strongly recommended naar set value as 0.
Electronic lock of de "bLC" besturing buttons
voor locking of besturing buttons it is required naar push en hold de button ▼ about 4 seconds before appearance op de screen of indication of bLC. After activation of this function when clicking any button op de screen indication of bLC will be removed. voor switching-off this function it is required naar push en hold de button about 5 seconds until op de screen of de device bLC will be displayed. This function is applied voor an exception of unwanted of random changes in settings of de device by de inexperienced user.
Switching op en switching off de device by besturing buttons
Switching off de device can be made met buttons op a front panel of de device. voor this purpose it is required naar press en hold voor 4 seconds de button ▲ Switching op is made by holding voor 2 seconds de same button.
Note:
in case of wire break of hitting of water in de Sensor, op de screen Err will be displayed. in case of short circuit of outputs of de Sensor op de screen will be displayed ЗНE.
Warranty liability
Guarantee use period of de device is 12 months from de day of sale. If de device broke down during de guarantee period, de manufacturer has naar do a repair during next 14 days from de moment of de device arrival naar de service. of replace device if it is beyond repair.
de device is beyond de guarantee repair in de cases, specified in this certificate: integrity damage of de seal; absence of de package box of operational manual met de warranty mark; presence of de tracks of opening; extern injury of de core, splits, cracks; internal damages of de parts; melted terminals; incorrect connection; water inside de device core, corrosion of de internal en extern components; natural factors (lightning) etc. in these cases repairing is carried out voor de buyer expenses.
de warranty voor servicing de device, which broke down through buyer fault, during de warranty period can be from 3 naar 6 months of before warranty period ending, depends op complexity of de breakage. de guarantee voor de post-warranty repair is 3 months.