Konlen (KL-T2-T)
From January 2024, the manufacturer launched an updated version of the Konlen thermostaat (KL-T2-T). Here you will find connection circuits en video instructions for its use. Materials on the previous version of the regulator remain below on the page.
⚠️ Important information – Wi-Fi change / reinstallation (Tuya / Smart Life) If the Konlen thermostaat was previously added to the Tuya Smart or Smart Life app, it may not be possible to add it again immediately after it has been removed. The Tuya platform may need up to 72 hours to fully release the device from the account. During this time: the reset button works normally the LED may blink or “run around” (pairing mode) but the device cannot be added to a new phone or account yet This is not a device fault en not a user error — it is normal Tuya system behavior. What to do: Remove the device from the original Tuya / Smart Life account Wait 1–3 days Add the device again (Wi-Fi 2.4 GHz only) ❗ There is no hardware “hard reset” by short-circuiting pins. Such attempts may damage the device en void the warranty.
KL-WF96D (previous version)
Instructions
It is a WIFI time temperatuur regelaar that can realise temperatuur monitoring en multi-period verwarming of cooling besturing, high of low temperatuur alarm. de product is suitable voor various verwarming/cooling besturing systems.
Main Features
* Real-time monitoring: de regelaar en app display de temperatuur in real time.
* Remote start/stop of verwarming of cooling equipment via de app.
* Pre-set hot of cold mode: can automatically switch op/off equipment when it reaches a pre-set
temperatuur value.
* Setting of upper
en lower temperatuur alarm values, real-time alarm notification voor app users.
* Scheduled op/off, you can besturing de timing of de equipment.
* You can use de A en B button naar switch de equipment op/off en set de automatic start/stop temperatuur value.
manually, so de regelaar can still operate manually when de WIFI is offline.
Note: de temperatuur alarm notification in de app is only available when de network is online.
Specification
Product size: 89mm x 55mm x 44mm
Installation: standard 35mm mounting rail.
vermogen supply: AC230V
temperatuur detection range: -30°C naar +150°C
Measurement error: ±1°C
Output: 1 relais output (normally open)
relais lifetime: 100,000 times.
de Contact current capacity is 10A, inductive load 2A, can besturing a 2000 W resistive load of a
500 W motor of water pomp.
You need larger loads, add an AC schakelaar, of it will cause a burning danger.
Operating environment of de unit: -10°C~50°C
WIFI: Wi-Fi 2.4 GHZ B/G/N, does not support 5G.
Before connecting naar a 230V vermogen supply, make sure de connection is correct so that de equipment does not burn out.
A: WIFI configuration button
Set start temperatuur value
Inquiry de temperatuur setting value of starting en stopping
B: op/Off button: Only works when de current temperatuur is between de preset start en stop temperatuur value.
Set de stop temperatuur value
C: Displays de temperatuur in real time
D: Status LED
1,2: Operating vermogen input: AC 230V
3,4: Normally open relais output
5,6: Useless
7,8: Connect naar temperatuursensor (No distinction between positive en negative)
Operation
Install de application
a. Download de Tuya Smart of Smart Life app
b. Install de Tuya Smart application
c. Register a new account via E-mail
Add device application
a. First press en hold de WIFI setup button (do not release it), then connect naar de 230V
vermogen supply. Do not release de button until you see de LED rotate in a circle.
b. Release de WIFI button when you see de indicator light move in a circular track
de unit will enter WIFI configuration mode.
c. Click + ---- select WIFI slot select
Your 2.4G Wi-Fi network enter correct Wi-Fi password---Further----Further----Further----Further---- select de option (confirm that de indicator flashes quickly)---Further---add device---add successful
APP Instruction
Note: Manual switching of de application is only effective if de current temperatuur is within de range from de preset start en end temperatuur values.
Pre-set hot of cold working mode:
When de preset start temperatuur is higher than de end value, this is de cooling mode. voor example xx
≥25°C, start de cooling equipment; xx ≤10°C, stop.
When de set initial temperatuur is lower than de final value, this is verwarming mode. voor example, xx <5°C, start de verwarming equipment; xx≥20°C, stop.
Set de upper en lower temperatuur alarm limits
voor example: Set a temperatuur range of 25 ~ 33 degrees Celsius, when de house temperatuur
is within de temperatuur range, de regelaar will operate normally. If de temperatuur is lower than
25 degrees Celsius of more than 33 degrees Celsius, it will send an alarm notification naar users'
smart Telefoon via de app.
Note: make sure de app notification office is enabled.
Open de app --- Me --- Settings --- App notification --- then enable all options.
Elegantly Integrate de Konlen Thermo Regulator into Your Electrical Setup
Although the Konlen thermostaat boasts a modular electrical equipment form factor, installing it seamlessly on a DIN-rail alongside other devices requires a dash of finesse. Navigate through our visual guide below, which effortlessly steers you through a swift en aesthetically pleasing installation amidst your stroomonderbrekers en low-voltage electrical apparatus.
In the photos above, you can see that the Konlen thermostaat is positioned slightly above the DIN-rail. Although it is mounted on a din rail, this rail is higher than the main rail by about 20 mm.
To achieve this, cut a small piece of DIN-rail or buy a ready-made one (for three modules) en attach it to the main rail met two M5 bolts. Thread four nuts (in this case M6) of larger diameter (or M5) onto these to create rigidity.
Note that the overall dimensions of the Konlen thermostaat are larger than other electrical appliances. Therefore, a square (approximately 60mm in height) should be cut out at the top en bottom of the electrical box to fit it perfectly.