Installation desirable teplota

​

  By short pressing button ▼ alebo ▲ device temporarily shows na screen specified desirable teplota. pre menu access pre changing desirable teplota it is required do press a hold down pre 2 seconds button ▼ alebo ▲ changeable value teplota will begin do blink. Further same buttons ▼ alebo ▲ do set desirable teplota a do fix button B.

​

 

Installation "rEJ" mode

​

  pre a start it is necessary do access menu device. pre this purpose it is required do push a hold pre 2 seconds button B. Then by short clicking na same button do select rEJ submenu. Further s button ▼ alebo ▲ do select one three options ( selected mode blinks) a do press shortly button B pre confirmation.

instrument has three options an operation mode:

1) nAG- vykurovanie

2) ohL- cooling

3) ocn- interval

v section "Installation teplota a Hysteresis" you can review how these modes work.

​

Installation teplota a hysteresis "GSt"

​

  pre a start it is necessary do enter menu device, pre this purpose it is required do press a hold down pre 2 seconds button B, then short pressing same button do select GSt submenu. Further do set s button ▼ alebo ▲ required value a hysteresis (changeable value blinks) a do press shortly button B pre confirmation.

​

  How hysteresis works?

​

  When mode vykurovanie nAG is selected: if desirable teplota is set as 30 °C a hysteresis will be set as 5 °C then relé device will turn na pri a teplota 25 °C, a is disconnected when 30 degrees, thereby maintaining teplota 25-30 °C.

When mode cooling ohL is selected: if desirable teplota is set as 30 °C a hysteresis is set as 5 °C, then relé device will turn na pri a teplota 35 °C, a is switched-off pri 30 °C, thereby maintaining teplota 35 a 30 °C.

When mode window OCN is selected: if desirable teplota is set as 30 °C a hysteresis is set as 5 °C, then relé instrument will turn na pri taken teplota from 25 °C do 35 °C, a switched-off if taken teplota is above 35 °C alebo below 25 °C.

​

Operation-time counter

​

This model heat regulátor has a built-v operation-time counter. time is calculated every second heat regulátor's operation a is saved v device internal memory every 15 minutes, even v case a výkon cut. calculated time is recorded v a heat regulátor's "trE" menu v increments one hour. A maximum recorded value is equal do 999 hours. When maximum value is reached, time count stops. You can resume counting by resetting counter. aim this function is do calculate energy consumed over a certain period time, pre example, over a month. do check alebo reset recorded time you need do enter heat regulátor's menu. v order do do it, press "В" button a hold it pre 2 seconds. Then press same button shortly a choose a trE submenu. After that you can access trE submenu do view recorded time by pressing ▼ alebo ▲ buttons. v order do reset counter, use ▼ alebo ▲ buttons do select “YES” value a press B button shortly do confirm your choice under trE menu.

​

senzor teploty calibration

​

First, you need do access regulátor’s menu. do do it, press "В" button a hold it pre 2 seconds. Then press same button shortly a choose a Cor submenu. Use ▼ alebo ▲ buttons do set a correction ( changeable value will blink), a press B button shortly pre confirmation.

​

​

Installation response delay device relé pre taken teplota changings "rEL".

​

  pre a start it is necessary do enter menu device, pre this purpose it is required do push a hold pre 2 seconds button B, then by short clicking same button do select rEL submenu. Further button ▼ alebo ▲ do set required delay period v seconds ( selected mode blinks) a do press shortly button B pre confirmation.

How time delay works:

After relé device turns na alebo turns off loading it won't response do changes taken teplota during specifies time even if indications taken teplota will quit out set limits.

Note:

if there is no obvious need pre a time delay reaction is strongly recommended do set value as 0.

​

Electronic lock "bLC" ovládanie buttons

​

  pre locking ovládanie buttons it is required do push a hold button ▼ about 4 seconds before appearance na screen indication bLC. After activation this function when clicking any button na screen indication bLC will be removed. pre switching-off this function it is required do push a hold button about 5 seconds until na screen device bLC will be displayed. This function is applied pre an exception unwanted alebo random changes v settings device by inexperienced user.

​

Switching na a switching off device by ovládanie buttons

​

  Switching off device can be made s buttons na a front panel device. pre this purpose it is required do press a hold pre 4 seconds button ▲ Switching na is made by holding pre 2 seconds same button.

Note:

v case wire break alebo hitting water v senzor, na screen Err will be displayed. v case short circuit outputs senzor na screen will be displayed ЗНE.

Warranty liability

Guarantee use period device is 12 months from day sale. If device broke down during guarantee period, manufacturer has do do a repair during next 14 days from moment device arrival do service. alebo replace device if it is beyond repair.

device is beyond guarantee repair v cases, specified v this certificate: integrity damage seal; absence package box alebo operational manual s warranty mark; presence tracks opening; externý injury core, splits, cracks; internal damages parts; melted terminals; incorrect connection; water inside device core, corrosion internal a externý components; natural factors (lightning) etc. v these cases repairing is carried out pre buyer expenses.

warranty pre servicing device, which broke down through buyer fault, during warranty period can be from 3 do 6 months alebo before warranty period ending, depends na complexity breakage. guarantee pre post-warranty repair is 3 months.