Konlen (KL-T2-T)
From January 2024, the manufacturer launched an updated version of the Konlen termostat (KL-T2-T). Here you will find connection circuits a video instructions for its use. Materials on the previous version of the regulator remain below on the page.
⚠️ Important information – Wi-Fi change / reinstallation (Tuya / Smart Life) If the Konlen termostat was previously added to the Tuya Smart or Smart Life app, it may not be possible to add it again immediately after it has been removed. The Tuya platform may need up to 72 hours to fully release the device from the account. During this time: the reset button works normally the LED may blink or “run around” (pairing mode) but the device cannot be added to a new phone or account yet This is not a device fault a not a user error — it is normal Tuya system behavior. What to do: Remove the device from the original Tuya / Smart Life account Wait 1–3 days Add the device again (Wi-Fi 2.4 GHz only) ❗ There is no hardware “hard reset” by short-circuiting pins. Such attempts may damage the device a void the warranty.
KL-WF96D (previous version)
Instructions
It is a WIFI time teplota regulátor that can realise teplota monitoring a multi-period vykurovanie alebo cooling ovládanie, high alebo low teplota alarm. product is suitable pre various vykurovanie/cooling ovládanie systems.
Main Features
* Real-time monitoring: regulátor a app display teplota v real time.
* Remote start/stop vykurovanie alebo cooling equipment via app.
* Pre-set hot alebo cold mode: can automatically switch na/off equipment when it reaches a pre-set
teplota value.
* Setting upper
a lower teplota alarm values, real-time alarm notification pre app users.
* Scheduled na/off, you can ovládanie timing equipment.
* You can use A a B button do switch equipment na/off a set automatic start/stop teplota value.
manually, so regulátor can still operate manually when WIFI is offline.
Note: teplota alarm notification v app is only available when network is online.
Specification
Product size: 89mm x 55mm x 44mm
Installation: standard 35mm mounting rail.
výkon supply: AC230V
teplota detection range: -30°C do +150°C
Measurement error: ±1°C
Output: 1 relé output (normally open)
relé lifetime: 100,000 times.
Kontakt current capacity is 10A, inductive load 2A, can ovládanie a 2000 W resistive load alebo a
500 W motor alebo water čerpadlo.
You need larger loads, add an AC stykač, alebo it will cause a burning danger.
Operating environment unit: -10°C~50°C
WIFI: Wi-Fi 2.4 GHZ B/G/N, does not support 5G.
Before connecting do a 230V výkon supply, make sure connection is correct so that equipment does not burn out.
A: WIFI configuration button
Set start teplota value
Inquiry teplota setting value starting a stopping
B: na/Off button: Only works when current teplota is between preset start a stop teplota value.
Set stop teplota value
C: Displays teplota v real time
D: Status LED
1,2: Operating výkon input: AC 230V
3,4: Normally open relé output
5,6: Useless
7,8: Connect do senzor teploty (No distinction between positive a negative)
Operation
Install application
a. Download Tuya Smart alebo Smart Life app
b. Install Tuya Smart application
c. Register a new account via E-mail
Add device application
a. First press a hold WIFI setup button (do not release it), then connect do 230V
výkon supply. Do not release button until you see LED rotate v a circle.
b. Release WIFI button when you see indicator light move v a circular track
unit will enter WIFI configuration mode.
c. Click + ---- select WIFI slot select
Your 2.4G Wi-Fi network enter correct Wi-Fi password---Further----Further----Further----Further---- select option (confirm that indicator flashes quickly)---Further---add device---add successful
APP Instruction
Note: Manual switching application is only effective if current teplota is within range from preset start a end teplota values.
Pre-set hot alebo cold working mode:
When preset start teplota is higher than end value, this is cooling mode. pre example xx
≥25°C, start cooling equipment; xx ≤10°C, stop.
When set initial teplota is lower than final value, this is vykurovanie mode. pre example, xx <5°C, start vykurovanie equipment; xx≥20°C, stop.
Set upper a lower teplota alarm limits
pre example: Set a teplota range 25 ~ 33 degrees Celsius, when house teplota
is within teplota range, regulátor will operate normally. If teplota is lower than
25 degrees Celsius alebo more than 33 degrees Celsius, it will send an alarm notification do users'
smart Telefón via app.
Note: make sure app notification office is enabled.
Open app --- Me --- Settings --- App notification --- then enable all options.
Elegantly Integrate Konlen Thermo Regulator into Your Electrical Setup
Although the Konlen termostat boasts a modular electrical equipment form factor, installing it seamlessly on a DIN-rail alongside other devices requires a dash of finesse. Navigate through our visual guide below, which effortlessly steers you through a swift a aesthetically pleasing installation amidst your circuit breakers a low-voltage electrical apparatus.
In the photos above, you can see that the Konlen termostat is positioned slightly above the DIN-rail. Although it is mounted on a din rail, this rail is higher than the main rail by about 20 mm.
To achieve this, cut a small piece of DIN-rail or buy a ready-made one (for three modules) a attach it to the main rail s two M5 bolts. Thread four nuts (in this case M6) of larger diameter (or M5) onto these to create rigidity.
Note that the overall dimensions of the Konlen termostat are larger than other electrical appliances. Therefore, a square (approximately 60mm in height) should be cut out at the top a bottom of the electrical box to fit it perfectly.