Konlen (KL-T2-T)
From January 2024, the manufacturer launched an updated version of the Konlen termostato (KL-T2-T). Here you will find connection circuits y video instructions for its use. Materials on the previous version of the regulator remain below on the page.
⚠️ Información importante – Cambio de Wi-Fi / reinstalación (Tuya / Smart Life) If the Konlen termostato was previously added to the Tuya Smart or Smart Life app, it may not be possible to add it again immediately after it has been removed. The Tuya platform may need up to 72 hours to fully release the device from the account. During this time: the reset button works normally the LED may blink or “run around” (pairing mode) but the device cannot be added to a new phone or account yet This is not a device fault y not a user error — it is normal Tuya system behavior. What to do: Remove the device from the original Tuya / Smart Life account Wait 1–3 days Add the device again (Wi-Fi 2.4 GHz only) ❗ There is no hardware “hard reset” by short-circuiting pins. Such attempts may damage the device y void the warranty.
KL-WF96D (previous version)
Instructions
It is a WIFI time temperatura controlador that can realise temperatura monitoring y multi-period calefacción o cooling Control, high o low temperatura alarm. el product is suitable para various calefacción/cooling Control systems.
Main Features
* Real-time monitoring: el controlador y app display el temperatura en real time.
* Remote start/stop de calefacción o cooling equipment via el app.
* Pre-set hot o cold mode: can automatically switch en/off equipment when it reaches a pre-set
temperatura value.
* Setting de upper
y lower temperatura alarm values, real-time alarm notification para app users.
* Scheduled en/off, you can Control el timing de el equipment.
* You can use el A y B button a switch el equipment en/off y set el automatic start/stop temperatura value.
manually, so el controlador can still operate manually when el WIFI is offline.
Note: el temperatura alarm notification en el app is only available when el network is online.
Specification
Product size: 89mm x 55mm x 44mm
Installation: standard 35mm mounting rail.
potencia supply: AC230V
temperatura detection range: -30°C a +150°C
Measurement error: ±1°C
Output: 1 relé output (normally open)
relé lifetime: 100,000 times.
el Contacto current capacity is 10A, inductive load 2A, can Control a 2000 W resistive load o a
500 W motor o water bomba.
You need larger loads, add an AC contactor, o it will cause a burning danger.
Operating environment de el unit: -10°C~50°C
WIFI: Wi-Fi 2.4 GHZ B/G/N, does not support 5G.
Before connecting a a 230V potencia supply, make sure el connection is correct so that el equipment does not burn out.
A: WIFI configuration button
Set start temperatura value
Inquiry el temperatura setting value de starting y stopping
B: en/Off button: Only works when el current temperatura is between el preset start y stop temperatura value.
Set el stop temperatura value
C: Displays el temperatura en real time
D: Status LED
1,2: Operating potencia input: AC 230V
3,4: Normally open relé output
5,6: Useless
7,8: Connect a Sensor de temperatura (No distinction between positive y negative)
Operation
Install el application
a. Download el Tuya Smart o Smart Life app
b. Install el Tuya Smart application
c. Register a new account via Correo electrónico
Add device application
a. First press y hold el WIFI setup button (do not release it), then connect a el 230V
potencia supply. Do not release el button until you see el LED rotate en a circle.
b. Release el WIFI button when you see el indicator light move en a circular track
el unit will enter WIFI configuration mode.
c. Click + ---- select WIFI slot select
Your 2.4G Wi-Fi network enter correct Wi-Fi password---Further----Further----Further----Further---- select el option (confirm that el indicator flashes quickly)---Further---add device---add successful
APP Instruction
Note: Manual switching de el application is only effective if el current temperatura is within el range from el preset start y end temperatura values.
Pre-set hot o cold working mode:
When el preset start temperatura is higher than el end value, this is el cooling mode. para example xx
≥25°C, start el cooling equipment; xx ≤10°C, stop.
When el set initial temperatura is lower than el final value, this is calefacción mode. para example, xx <5°C, start el calefacción equipment; xx≥20°C, stop.
Set el upper y lower temperatura alarm limits
para example: Set a temperatura range de 25 ~ 33 degrees Celsius, when el house temperatura
is within el temperatura range, el controlador will operate normally. If el temperatura is lower than
25 degrees Celsius o more than 33 degrees Celsius, it will send an alarm notification a users'
smart Teléfono via el app.
Note: make sure el app notification office is enabled.
Open el app --- Me --- Settings --- App notification --- then enable all options.
Elegantly Integrate el Konlen Thermo Regulator into Your Electrical Setup
Although the Konlen termostato boasts a modular electrical equipment form factor, installing it seamlessly on a DIN-rail alongside other devices requires a dash of finesse. Navigate through our visual guide below, which effortlessly steers you through a swift y aesthetically pleasing installation amidst your interruptor automáticos y low-voltage electrical apparatus.
In the photos above, you can see that the Konlen termostato is positioned slightly above the DIN-rail. Although it is mounted on a din rail, this rail is higher than the main rail by about 20 mm.
To achieve this, cut a small piece of DIN-rail or buy a ready-made one (for three modules) y attach it to the main rail con two M5 bolts. Thread four nuts (in this case M6) of larger diameter (or M5) onto these to create rigidity.
Note that the overall dimensions of the Konlen termostato are larger than other electrical appliances. Therefore, a square (approximately 60mm in height) should be cut out at the top y bottom of the electrical box to fit it perfectly.